# Op Amps .pdf

### File information

Original filename:

**Op Amps.pdf**

This PDF 1.5 document has been generated by TeX / pdfTeX-1.40.16, and has been sent on pdf-archive.com on 19/02/2016 at 10:05, from IP address 73.170.x.x.
The current document download page has been viewed 1190 times.

File size: 385 KB (13 pages).

Privacy: public file

### Share on social networks

### Link to this file download page

### Document preview

Operational Amplifier Circuits

Adam Barker

Partner: Keyan Chang

EE 101/L, Winter 2016

Prof. Joel Kubby

Lab TA: Jos Armando Oviedo

Section 5 - Thursday

February 19, 2016

Abstract

In this lab we investigate the the properties of operational amplifiers. An operational amplifier takes two electrical inputs along with up to two sources of power

and outputs the differnce between the two input potentials as the output potential.

Utilizing feedback through combinations of resistors and/or capacitors in parallel, the

operational amplifier can amplify the output potential or act as more complicated circuit elements like differentiators and integrators which we also investigate. In this lab

we measure how these outputs relate to the inputs and power supplies and verify the

functionality of these circuit elements.

1

1

Introduction

Although the internal circuitry is beyond what we will investigate in this lab, at its core, an

operational amplifier (hereafter called op-amps) creates a potential at its output terminal

proportional to the difference between the two input potentials. A circuit diagram for an

ideal op-amp is shown in Figure 1.

Figure 1: Equivalent circuit for an idea op-amp. The open-loop gain, AOL is very large.

An op-amp has two input terminals, the non-inverting input and the inverting input. For

a voltage of v1 applied at the non-inverting input and a voltage of v2 applied at the inverting

input, the op-amp will produce at its output terminal a potential equal to the product of the

open-loop gain, AOL , and the potential difference between the input voltages, vid = (v1 − v2 ).

This can be expressed as v0 = AOL (v1 − v2 ). The open-loop gain is ideally very large and

constant, this will be useful when we implement negative feedback in the circuit as it allows

the circuit to satisfy the summing-point constraint for a wide variety of input voltages. For

our experiment we use the LM741 op-amp, which has AOL on the order of 2 × 105 . The

circuit symbol for the op-amp is shown in Figure 2, the inputs Vcc and Vee are the positive

and negative power supplies respectively. An op-amp is limited to producing only output

voltages within the strict range of Vee ≤ v0 ≤ Vcc .

Figure 2: Symbolic representation of an op-amp, including power supplies Vee and Vcc .

2

The basic op-amp circuit we investigate in this lab is called the inverting amplifier, or the

basic inverter. The circuit diagram for the basic inverter is shown in Figure 3. It consists of

an input potential fed through some input resistor, R1 , into the inverting input of the op-amp

with the non-inverting input leading directly to the ground. The output terminal applies its

voltage across some element RL . Most importantly however is the resistive element linking

the output back to the inverting input, R2 . This element creates what is known as negative

feedback, and is the necessary factor in allowing the op-amp to work as an amplifying circuit.

Figure 3: Circuit diagram for the basic inverter, including the input resistance, R1 , the

feedback resistor, R2 , and the load resistor, RL .

Because the open-loop gain is very large, any input voltage, Vin , no matter how small will

result in a large output voltage from the op-amp with opposite polarity with respect to the

input. Some of this output voltage is fed through the feedback resistor back to the inverting

input terminal. Subsequently, because the output voltage has opposite polarity to the input

voltage, the voltage at the inverting input terminal is instantaneously driven towards zero,

and over a very short time scale (related to the open-loop gain and other factors internal to

the op-amp) it will reach zero exactly. This negative feedback creates what is known as the

summing point-constraint, that is, that the potential difference between the input terminals

of an ideal op-amp is necessarily zero at all times, provided that negative feedback exists in

the circuit.

Since the input voltage is applied across the input resistor, R1 , we can say from Ohm’s

law that the current through R1 is i1 = vRin1 . But because of the summing-point constraint,

the input and output voltages of the op-amp are zero, and so no current may flow through

it. Thus the current i1 can only flow through the feedback resistor, R2 , so we may say

that i2 = i1 . Applying Kirchoff’s Voltage Law from ground through the load resistor, then

the feedback resistor, across the input terminals, and back to ground (keeping in mind the

summing-point constrain), we obtain the relation v0 + R2 i2 = 0. Substituting the relation

i2 = i1 = vRin1 from earlier we find that

v0

R2

=−

= Av

vin

R1

We call Av the closed-loop gain, and it is the ratio between the voltage across some load and

the input voltage when the circuit is closed. Thus we have constructed the simple circuit

3

Figure 4: Basic principles of a capacitor. [Source: Wikipedia.org]

known as the basic inverting amplifier.

Before we continue with more complicated circuits, it is necessary to discuss the basic

principles of capacitors and their capacitance. Figure 4 shows the basic principles of a

capacitor. A capacitor consists of two conducting plates separated by a non-conducting

region known as the dielectric. When a voltage is applied across a capacitor, for example by

a battery, positive charges are driven towards one plate and negative charges towards the

other. However, the charges cannot cross from one plate to another due to the insulating

properties of the dielectric. And so, an electric field is created between the plates proportional

to the voltage applied across them. This effect can be characterized as such

C=

Q

V

Here Q is the net charge on each plate, V is the voltage applied, and C is known as the

capacitance of the capacitor. The capacitance of the capacitor is a function of the area of

the plates, their separation, and the electric permittivity of the dielectric. It can be written

as

A

C = r 0

d

Here, A is the area of the two plates, d their separation, 0 the vacuum permittivity, and r

the relative permittivity of the dielectric. Since current is the time rate of change of charge,

we can differentiate the equation above to get the current flowing ”through” the capacitor

as a function of the voltage

dV (t)

I(t) = C

dt

We say the current flows through the capacitor only to express the motion of charges in the

system, in reality charges cannot flow like this due to the insulating nature of the dielectric.

Figure 5 shows the circuit diagram for the basic integrator circuit. Although similar in

design an concept to the basic inverting amplifier, the integrator has the effect of producing

4

Figure 5: Circuit diagram for the basic integrator, including the input resistance, R1 , the

feedback capacitor, C, and the load resistor, RL .

an output voltage at its terminal proportional to the time-integral of the input voltage from

the time the circuit starts. Like earlier we first look at the current through R1 as a result of

the input voltage, however, it is now helpful to consider some time-dependant voltage vin (t)

rather than the steady-state input we considered before. Here we see

iin (t) =

vin (t)

R1

, and consequently from the summing-point constraint we again see that iC (t) = iin (t). From

our capacitor equation this becomes

C

dvc (t)

= iin (t)

dt

Rearranging this equation and integrating we get

Z

1 t

vc (t) =

iin (t)dt

C 0

Applying KVL through the output load, the capacitor, and the input terminals, and keeping

in mind the summing-point constraint we obtain v0 (t) = −vc (t). Substituting our earlier

equation we can solve this circuit for its characteristic equation

Z t

1

v0 (t) = −

vin (t)dt

R1 C 0

This shows, as stated earlier, that our integrator circuit produces a voltage proportional to

the running-time integral of the input voltage, with the constant of proportionality equal to

− R11C .

Figure 6 shows another similar circuit diagram, this time for the basic differentiator

circuit. This circuit will produce an output voltage proportional to the time-derivative of

5

Figure 6: Circuit diagram for the basic differentiator, including the input capacitance, C,

the feedback resistor, R1 , and the load resistor, RL .

the input voltage. Firstly we look at the current passing through the input capacitance.

Since the input voltage is strictly applied across the capacitor and the voltage at the other

end is zero due to the summing-point constraint we get that

iin = C

dvi n(t)

dt

This then is equal to the current flowing through the feedback resistor, ir . Application of

KVL through the output resistor, the feedback resistor and the input terminals tells us that

ir = −

v0

R1

Combining these equations we get that

v0 = −R1 C

dvin

dt

This shows, as stated earlier, that our differentiator circuit produces a voltage proportional

to the time-derivative of the input voltage, with constant of proportionality equal to −R1 C.

Lastly, we note that in practicality, an integrator circuit as described above is not necessarily optimal for all inputs. When the frequency of the input voltage is very low, or when

the input voltage is a constant (i.e. a frequency of zero), our integrator circuit will produce

a voltage that is ever growing, and it will continue to grow until the voltage reaches in magnitude the power supply voltage. This is not a particularly useful property of an integrator,

so, in practice we attach a large resistor across the capacitor. This has the effect of turning

the integrator into a basic inverting amplifier when the input frequency is low. This drives

the output voltage back towards zero, and prevents the output from reaching saturation,

and when the frequency is higher, due to the high resistance of the resistor, the functionality

of the integrator is not particularly impaired.

6

2

Experiment

2.1

DC Amplification

Figure 7: Circuit diagram for the first experiment.

A circuit was constructed according to the diagram in Figure 7. By inspection we see

that this is identical to the basic inverting amplifier circuit we described before. Thus we

R2

= 2.021. Applying a DC voltage at Vin and varying

expect to see a voltage gain of Av = R

1

it from -5V to +5V we observe across V0 voltages as found in Table 1.

We then expanded our data to include voltages from -10V to +10V. This continued data is

found in Table 2.

Inverting Amplifier

Vin (Volts) V0 (Volts)

-5

-9.896

-4

-7.916

-3

-5.939

-2

-3.958

-1

-1.974

0

0.000

1

1.969

2

3.950

3

5.930

4

7.911

5

9.893

Table 1: Voltage across the output terminal vs. input voltage for the basic inverting

amplifier.

7

Inverting Amplifier

Vin (Volts) V0 (Volts)

-10

-13.949

-9

-13.960

-8

-13.972

-7

-13.846

-6

-11.871

6

11.868

7

13.245

8

13.227

9

13.209

10

13.191

Table 2: Expanded voltage across the output terminal vs. input voltage for the basic

inverting amplifier.

Then we set our source voltage to Vin = 3V. We measured the current through the input

resistor, and we measured it to be 4.355 mA.

2.2

AC Amplification with Integrators and Differentiators

We then switched our DC voltage source out for an AC voltage source, and set vin = 1Volt

with frequency of 100 Hz. A peak to peak time difference of δt = 5ms was observed between

vin and v0 .

Next we increased the amplitude of the 100 Hz input voltage to vin = 8Volts. We observed

that the output voltages reached saturation at each peak at a value of around vm ax =

±14.2Volts.

We then switched out the input resistor with one of size R1 = 9.958kΩ and our feedback

resistor with a capacitor of capacitance C = 0.1µF . This then creates an integrator with

1

= 996 × 10−6 . Refer to Figure 5 for the circuit diagram

constant of proportionality − RC

of such a circuit. We observe that as the frequency of our input voltage increases, that the

magnitude of the output voltage decreases.

We then varied the frequency of the input voltage, f , and measured the ratio of the output

voltage magnitude to the input magnitude as G = vvin0 . This data can be seen in Table 3.

Next we observed the phase shift between the output and input voltages as a function of

frequency. This data can be seen in Table 4.

8

Integrator Circuit

f (Hz) G (unitless)

100

1.438

200

0.775

300

0.538

400

0.405

500

0.330

600

0.280

700

0.240

800

0.208

900

0.185

1000

0.168

2000

0.0863

3000

0.0600

4000

0.0435

Table 3: Frequency response of the integrator circuit.

Integrator Circuit

f (Hz) φ (degrees)

100

96.74◦

500

92.31◦

1000

91.55◦

3000

94.66◦

5000

89.06◦

7000

90.71◦

10000

88.57◦

Table 4: Phase change vs. frequency of the integrator circuit.

Next, we then switched our input resistor and feedback capacitor with eachother This

then created a differentiator with constant of proportionality −RC = 0.996 × 10−3 . Refer to

Figure 6 for the circuit diagram of such a circuit. We observe that as the frequency of our

input voltage increases, that the magnitude of the output voltage increases.

We then varied the frequency of the input voltage, f , and measured the ratio of the output

voltage magnitude to the input magnitude as G = vvin0 . This data can be seen in Table 5.

Next we observed the phase shift between the output and input voltages as a function of

frequency. This data can be seen in Table 6.

9

### Link to this page

#### Permanent link

Use the permanent link to the download page to share your document on Facebook, Twitter, LinkedIn, or directly with a contact by e-Mail, Messenger, Whatsapp, Line..

#### Short link

Use the short link to share your document on Twitter or by text message (SMS)

#### HTML Code

Copy the following HTML code to share your document on a Website or Blog